Delta Bathroom Tub Faucet Parts

Delta bathroom tub faucets are known for their durability, style, and functionality. However, even the best faucets can develop problems over time. If your Delta tub faucet is leaking, dripping, or not working properly, you may need to replace some of its parts. Fortunately, most Delta tub faucet parts are relatively easy to replace, and you can usually do the job yourself with a few simple tools.

Identifying the Parts of Your Delta Tub Faucet

Before you can replace any parts, you need to identify the parts that need to be replaced. The following diagram shows the major parts of a Delta tub faucet:

Handle
Escutcheon
Valve cartridge
Aerator
Supply lines
Drain assembly

Replacing the Handle

The handle is the part of the faucet that you use to turn the water on and off. If the handle is loose, cracked, or broken, you will need to replace it. To replace the handle, follow these steps:

Turn off the water supply to the faucet.
Remove the set screw that is located on the bottom of the handle.
Pull the handle straight up to remove it from the faucet.
Install the new handle by pushing it down onto the faucet body until it clicks into place.
Tighten the set screw.
Turn on the water supply and check for leaks.

Replacing the Escutcheon

The escutcheon is the decorative plate that covers the base of the faucet. If the escutcheon is cracked, chipped, or discoloured, you can replace it. To replace the escutcheon, follow these steps:

Turn off the water supply to the faucet.
Remove the screws that are holding the escutcheon in place.
Pull the escutcheon straight up to remove it from the faucet.
Install the new escutcheon by pushing it down onto the faucet body until it clicks into place.
Tighten the screws.
Turn on the water supply and check for leaks.

Replacing the Valve Cartridge

The valve cartridge is the part of the faucet that controls the flow of water. If the valve cartridge is worn out, damaged, or clogged, you will need to replace it. To replace the valve cartridge, follow these steps:

Turn off the water supply to the faucet.
Remove the handle and escutcheon.
Use a wrench to loosen the packing nut that is located behind the escutcheon.
Pull the valve cartridge straight out of the faucet body.
Install the new valve cartridge by pushing it into the faucet body until it clicks into place.
Tighten the packing nut.
Reinstall the escutcheon and handle.
Turn on the water supply and check for leaks.

Replacing the Aerator

The aerator is the small, screen-like device that is located at the end of the faucet spout. The aerator helps to mix air with the water, which creates a more forceful and consistent stream of water. If the aerator is clogged or damaged, you will need to replace it. To replace the aerator, follow these steps:

Turn off the water supply to the faucet.
Use a wrench or pliers to unscrew the aerator from the faucet spout.
Inspect the aerator for any clogs or damage.
If the aerator is clogged, you can try to clean it by soaking it in vinegar or CLR for a few hours.
If the aerator is damaged, you will need to replace it.
To install the new aerator, simply screw it onto the faucet spout.
Turn on the water supply and check for leaks.

Replacing the Supply Lines

The supply lines are the flexible hoses that connect the faucet to the water supply. If the supply lines are cracked, kinked, or leaking, you will need to replace them. To replace the supply lines, follow these steps:

Turn off the water supply to the faucet.
Disconnect the supply lines from the faucet and from the water supply.
Install the new supply lines by connecting them to the faucet and to the water supply.
Turn on the water supply and check for leaks.

Replacing the Drain Assembly

The drain assembly is the part of the faucet that allows water to drain from the sink. If the drain assembly is clogged, leaking, or damaged, you will need to replace it. To replace the drain assembly, follow these steps:

Turn off the water supply to the faucet.
Remove the stopper from the drain.
Use a wrench or pliers to loosen the drain assembly from the sink.
Pull the drain assembly straight out of the sink.
Install the new drain assembly by inserting it into the sink and tightening it with a wrench or pliers.
Replace the stopper.
Turn on the water supply and check for leaks.

Conclusion

Replacing Delta bathroom tub faucet parts is a relatively easy task that can be done with a few simple tools. By following the steps outlined in this article, you can quickly and easily repair your faucet and get it working properly again.